எச்.எல்.ஜி -150 எச் சராசரி நீர்ப்புகா எல்.ஈ.டி மின்சாரம்

Model

HLG-150H-12

HLG-150H-15

HLG-150H-24

Output

DC VOLTAGE

12V

15V

24V

CURRENT ADJ. RANGE

Can be adjusted by internal potentiometer A type only

7.5-12.5A

6-10A

3.8-6.3A

RATED POWER

150W

150W

151.2W

VOLTAGE ADJ. RANGE

10.8-13.5V

13.5-17V

22-27V

Input

Voltage Range

90-264VAC           127-370V DC

Frequency Range

47-63Hz

POWER FACTOR

PF>0.98/115VAC, PF>0.95/230VAC, at full load (Please refer to "Power Factor Characteristic" curve)

Efficiency(Typ.)(230Vac)

92%

92.5%

93.5%

AC CURRENT (Typ.)

1.7A / 115VAC          0.75A / 230VAC

INRUSH CURRENT(Typ.)

COLD START 75A/230VAC

LEAKAGE CURRENT

<0.75mA / 240VAC

PROTECTION

OVER LOAD

95~ 108%

Protection type : Constant current limiting, recovers automatically after fault condition is removed

SHORT CIRCUIT

Constant current limiting, recovers automatically after fault condition is removed

OVER VOLTAGE

14-17V

18-21V

28-34V

Protection type :Shut down O/P voltage, re-power on to recover

OVER TEMPERATURE

100 ℃ up or less10 ℃ (RTH2)

Protection type : Shut down and latch off o/p voltage, recovers automatically after temperature goes down

Environment

WORKING TEMP.

-40 ~ +70 ℃(Refer to output load derating curve)

WORKING HUMIDITY

20 ~ 95% RH non-condensing

SAFETY

SAFETY STANDARDS

UL8750, CSA C22.2 No. 250.0-08, EN61347-1, EN61347-2-13 independent IP65 or IP67, J61347-1, J61347-2-13 approved ;

design refer to UL60950-1, TUV EN60950-1

WITHSTAND VOLTAGE

I/P-O/P:3.75KVAC   I/P-FG:2KVAC     O/P-FG:0.5KVAC

ISOLATION RESISTANCE

I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC / 25 / 70% RH

EMC EMISSION

Compliance to EN55015, EN55022 (CISPR22) Class B, EN61000-3-2  Class C ( 50% load) ; EN61000-3-3

EMC IMMUNITY

Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, EN55024, light industry level (surge 4KV),  criteria A

Others

MTBF

192.2K hrs min.      MIL-HDBK-217F (25℃ )

DIMENSION

228*68*38.8mm (L*W*H)

PACKING

1.15Kg; 12pcs/14.8Kg/0.8CUFT

Note

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. Derating may be needed under low input voltages. Please check the static characteristics for more details.

5. Type A only.

6. Safety and EMC design refer to EN60598-1, CNS15233, GB7000.1, FCC part18.

7. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time.

8. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

9. Refer to warranty statement.